Mopar Parts & Accessories Archives - Schwartz Performance

Gen III Hemi & Hellcat Power Steering Pump Adapter 6AN

SchwartzP — Tue, 25 Aug 2020 20:51:07 +0000

Let me guess. Your Mopar power steering pump didn’t come with any way to attach a hose to it?
This fitting threads right into your stock Mopar power steering pump on all Gen 3 Hemi’s (and Hellcat & Hellephant) and converts it to a 6AN male fitting. It’s made of steel! Some of the other ones out there are aluminum and you have to be extra careful to not break it when tightening into the pump, and tightening the hose end onto it. With this steel one, you can have peace of mind.
It seals with an O-ring so don’t put any thread sealer on it. Just dab a tiny bit of oil on the O-ring.

The post Gen III Hemi & Hellcat Power Steering Pump Adapter 6AN appeared first on Schwartz Performance.

Hellcat Fuel Rail Fitting – Connector – Adapter 8AN 10AN

SchwartzP — Wed, 18 Mar 2020 20:50:47 +0000

This billet aluminum Hellcat/Demon/Hellephant fuel rail fitting fits on the 1/2″ male fuel rail and adapts to 8AN or 10AN male.

They feature high temp dual Viton O-rings and a steel snap ring to securely hold the fitting in place just like OEM!

Not to mention they are the LOWEST PROFILE fitting available for the Hellcat fuel rail.

The post Hellcat Fuel Rail Fitting – Connector – Adapter 8AN 10AN appeared first on Schwartz Performance.

Gen 3 Hemi Engine Lifting Brackets – 5.7 6.1 6.2 6.4

SchwartzP — Mon, 11 Nov 2019 23:05:08 +0000

We ran into a problem. That problem was, “how do we lift this Hellcat engine and not scratch the supercharger or valve covers?
We came up with this solution!
Sold as a set of 4, these brackets are flame cut & TIG welded to match all Gen 3 Hemi exhaust port mounting holes. Bolts are included, to mount them to your heads! Use some anti-seize though to prevent galling.
You will need to disconnect the exhaust manifolds, and that’s it! The brackets are designed to fit around OEM valve covers. They have a hole at the top for you to bolt a chain to, or some other fastening device to your hoist.

These are uncoated steel, and will rust over time. If that’s a problem for you, wipe some WD40 on them, paint them, etc.
We would powdercoat them, but after the first use they would not look so good anymore.

Flat cost shipping within the USA is $20. If you’re outside the 48 states, please give us a call or email for a quote.

The post Gen 3 Hemi Engine Lifting Brackets – 5.7 6.1 6.2 6.4 appeared first on Schwartz Performance.

Hellcat Supercharger Intercooler Manifold Adapters – Billet Aluminum AN

tkdigital — Wed, 28 Nov 2018 23:03:34 +0000

Make your Hellcat swap a little easier by ditching the large cast intercooler manifold on the factory Hellcat / Demon superchargers, and replace with our exclusive billet adapters!
The passenger side manifold is about 1 inch shallower than the factory Hellcat piece, NOT INCLUDING the pesky temp sensor that sticks off even further!

With our manifolds, you can choose your own path for the intercooler hoses, and use #10 AN hose instead of ugly rubber hose or attempting to adapt factory hoses.

Our kit includes:
-(1) LH and (1) RH billet aluminum manifold
-(4) #10 AN to O-ring adapters
-(1) #10 AN to NPT fitting adapter for temp sensor
-(1) 1/8″ NPT allen plug
-(1) #10 O-ring low profile allen plug
-(2) Assembled #10 AN hoses for connecting the two manifolds together

***You will need to furnish the in/out side of the blocks to your reservoir/pump/heat exchanger using #10 AN O-ring adapters of your choice. Straight or 45 degree swivel adapters will work, with a 90 or 45 degree hose end attached.***

ITEMS TO REUSE OR SOURCE FROM A PARTS STORE/DEALER:
-(1) Mopar water temp sensor
-(1) 1/8NPT bleeder
-(4) Torx button head bolts

The post Hellcat Supercharger Intercooler Manifold Adapters – Billet Aluminum AN appeared first on Schwartz Performance.

Hellcat Rear Sump Oil Pan, 6.2L Supercharged Hemi

tkdigital — Wed, 28 Nov 2018 23:03:34 +0000

This Hellcat-specific oil pan is designed for lowered cars with front-steer suspensions where the center or front sump will not work. Includes oil pan pickup AND bolts!

The wide sump increases capacity yet allows ample ground clearance. Fully baffled for competition use. Stock steering is NOT compatible with this pan! Use the center-sump Hellcat pan for stock suspensions.

Pan Capacity is 9 Qts. Plus Filter
Sump: 7 1/2″ Long, 13 1/2″ Wide, 8″ Deep

Milodon pan part number: 31032
Milodon pickup part number (Included): 18348

REUSE YOUR STOCK CRATE ENGINE GASKET; OR IF YOUR ENGINE IS USED, BUY A NEW MOPAR OIL PAN GASKET FROM A DEALER: PART NUMBER 68165605AA

The post Hellcat Rear Sump Oil Pan, 6.2L Supercharged Hemi appeared first on Schwartz Performance.