Check out the video below to view our latest shop updates & new projects!
Author: Schwartz Performance
-

1948-1952 Ford F1 Pickup Truck Chassis

NOW AVAILABLE! THE ULTIMATE UPGRADE FOR YOUR VINTAGE FORD F1 PICKUP!
Your original truck chassis is inherently weak. Our G-Machine Chassis isn’t.
The old, weak frame that your cab/bed, suspension components, and engine are mounted to begins to flex dramatically once you add more horsepower, higher spring-rates and better brakes; not to mention it’s over 60 years old. With our G-Machine Chassis, your Ford F1’s body will encounter much less flex and better ride quality, resulting in an all-around performing vehicle. Sure, you can box the original chassis and add new components; but would you build a HOUSE without a solid foundation?
Want your truck to handle like a newer sports car? You’ve chosen the right chassis.
The G-Machine Chassis is available for 1948, 1949, 1950, 1951 & 1952 Ford F1 pickup trucks.
Looking for a chassis for a pre-1948 or post-1952 Ford truck? We build custom frames for any make & model, contact us for details
Installation is simple.
- Our bolt-in design integrates all of the original core support, cab, and bed mounting points
- The floorpan does not need to be cut out, although some transmissions will require tunnel modification
- Our design offers much more strength over the stock frame, with plenty of room for exhaust
- We’ve designed this chassis to accept big block & small block Ford engines, as well as DOHC mod motors like the 4.6L and 5.0L Coyote (rear sump oil pan required on all engines). We can cater to virtually any engine/trans combo!
Want wider tires?
- All G-Machine Chassis allow for up to 345mm-wide rear tires if you minitub the bed sides.
- The Moser full-floating 9″ rear end is narrowed to 60″ to allow fitment for deeper dish wheels (different rear end widths available, too!)
Which options do I choose?
Brakes:
-Step up to the 14-inch Baer 6P Pro-Plus and get a brake system that will suit whatever you want to do. We race our 1965 Tempest often with this brake setup.
-The baddest kit is the Baer 6S, which is a one-piece forged caliper. This brake kit suits the hardcore roadracer, but does not sacrifice street driving.
-The 14″ brakes require a 18″ diameter wheel, however. Additionally, the Baer calipers are available in many colors.
Coilover shocks:
-We use RideTech coilovers as standard on our chassis systems. The two options we offer are single-adjustable and triple-adjustable.
-Single adjustable coilovers offer 24 “clicks” of adjustment for damping, as well as ride height adjustment. These will suit the weekend autocrosser/roadracer, as well as daily drivers.
-Triple adjustable coilovers offer the same damping adjustment as the singles with the addition of high and low speed compression adjustments, and a remote reservoir. These allow you to fine-tune your suspension for a specific type of driving. These are recommended for those who are willing & able to spend time tuning the shocks, and/or for the roadracer where every thousandth of a second counts.
-Air ride is also available, please call for pricing & info.
Rear end housing:
-Our standard axle is a Moser full-floating 9″ style housing, with 31-spline axles. We have tested this rear end up to 1000hp street cars with no issues. Contact us for higher HP, or if you’ll be drag racing it often on slicks with over 800hp.
-The Heidts IRS option is for those craving an IRS in their musclecar. This is recommended for up to 700hp.
Third member/differential:
-The Ford 9″ comes with a clutch-type posi. Our first option is just that, with a cast-iron center section. If you have less than 500hp and won’t be racing the car often, this is just fine for you.
-The Detroit TrueTrac differential is a helical-gear type posi, which holds up to more power than the clutch posi, lasts longer (no wearable parts), and is quiet enough for street cars.
-Moser offers a new nodular iron case which is recommended for 600+ hp and racing. Their aluminum case also holds up to higher horsepower, and is much lighter than iron cases.Pictures:
(Click to enlarge)



























Base price includes:
- A fully welded chassis, built on a precision jig
- Adjustable transmission crossmember
- All front and rear suspension components (excluding coilovers): control arms, ball joints, tie rods, power rack & pinion, aluminum front wheel hubs with bearings, and teflon-lined heim joints for a quieter & bind-free suspension
- BASE PRICE DOES NOT INCLUDE ANY BRAKES, SHOCKS, OR REAR END. CHOOSE THOSE ITEMS BELOW
Payment terms: 75% down at time of order, remaining 25% due before shipment.
Shipping: For an assembled frame, we use an enclosed car transporter. If you don’t want the frame assembled, we’ll ship it truck freight in a crate. There is a crating fee which will be determined upon ordering.
Pricing below is only for reference. Please call to order.
Pricing:
-

1967-1972 Chevy C10 GMC Chassis

Details:
A bolt-in modern high performance full-length frame & chassis system for 1967, 1968, 1969, 1970, 1971, and 1972 GMC & Chevrolet C10 pickups:
- Chevrolet C10 short-bed
- GMC C10 short-bed
Our full frames for 1967-1972 Chevrolet & GMC C10 trucks fasten to the cab & bed the same way your stock frame does. There is no floor cutting required (except for some transmisions), and the ride height is dropped from stock about 4 inches. The Ridetech coilovers used have adjustment for damping and ride height to give your truck an edge in autocross competitions as well as the ability to have a comfortable ride. All of our chassis utilize the same suspension geometry, which means your truck will now have all modern suspension and steering components and geometry.
This Schwartz chassis allows up to a 345 wide tire to fit in your [mini-tubbed] wheel wells, & we recommend up to a 315 wide front tire, but a 335 front will also fit.
For 15″ or 16″ rims we recommend our 12″ brake kit. Call for pricing.Which options do I choose?
Brakes:
-Step up to the 14-inch Baer 6P Pro-Plus and get a brake system that will suit whatever you want to do. We race our 1965 Tempest often with this brake setup.
-The baddest kit is the Baer 6S, which is a one-piece forged caliper. This brake kit suits the hardcore roadracer, but does not sacrifice street driving.
-The 14″ brakes require a 18″ diameter wheel, however. Additionally, the Baer calipers are available in many colors.
Coilover shocks:
-We use RideTech coilovers as standard on our chassis systems. The two options we offer are single-adjustable and triple-adjustable.
-Single adjustable coilovers offer 24 “clicks” of adjustment for damping, as well as ride height adjustment. These will suit the weekend autocrosser/roadracer, as well as daily drivers.
-Triple adjustable coilovers offer the same damping adjustment as the singles with the addition of high and low speed compression adjustments, and a remote reservoir. These allow you to fine-tune your suspension for a specific type of driving. These are recommended for those who are willing & able to spend time tuning the shocks, and/or for the roadracer where every thousandth of a second counts.
-Air ride is also available, please call for pricing & info.
Rear end housing:
-Our standard axle is a Moser full-floating 9″ style housing, with 31-spline axles. We have tested this rear end up to 1000hp street cars with no issues. Full-floating axle setups are becoming the norm in the pro-touring world. For more information on full floaters, click here: Full Floating Rear End Advantages.
Contact us for higher HP, or if you’ll be drag racing it often on slicks with over 800hp; We’ll set you up with something heavy duty.
-The Heidts IRS option is for those craving an IRS in their musclecar. This is recommended for up to 700hp, but has been tested without failure on higher horsepower cars.
Third member/differential:
-The Ford 9″ comes with a clutch-type posi. Our first option is just that, with a cast-iron center section. If you have less than 500hp and won’t be racing the car often, this is just fine for you.
-The Detroit TrueTrac differential is a helical-gear type posi, which holds up to more power than the clutch posi, lasts longer (no wearable parts), and is quiet enough for street cars.
-Moser offers a new nodular iron case which is recommended for 600+ hp and racing. Their aluminum case also holds up to higher horsepower, and is much lighter than iron cases.Pictures:
(Click to enlarge)



























Base price includes:
- A fully welded chassis, built on a precision jig
- Adjustable transmission crossmember
- All front and rear suspension components (minus coilovers): control arms, ball joints, tie rods, power rack & pinion, aluminum front wheel hubs with bearings, and teflon-lined heim joints for a quieter & bind-free suspension
- BASE PRICE DOES NOT INCLUDE ANY BRAKES, SHOCKS, OR REAR END. CHOOSE THOSE ITEMS BELOW
Payment terms: 75% down at time of order, remaining 25% due before shipment.
Shipping: For an assembled frame, we use an enclosed car transporter. If you don’t want the frame assembled, we’ll ship it truck freight in a crate. There is a crating fee which will be determined upon ordering.
Pricing below is only for reference. Please call to order.Pricing- Choose your options below:
-

1963-1967 Corvette C2 Chassis

Now available!
Our C2 chassis utilizes factory C5/C6 front suspension, and C4 rear suspension. We ditch the leaf springs and offer RideTech HQ coilover shocks. To control the lean, heavy duty splined sway bars are added front and rear.
A Mustang style power rack & pinion is standard, and allows for an easier steering shaft connection (compared to the C5/C6 rack).We recommend flaring the fenders to fit wide wheels/tires.
This chassis bolts to the factory mounts with no floorpan cutting required. Some clearancing behind the seats and of the tunnel is required. Transmission choice may also require transmission tunnel modification.
These are a very worthwhile upgrade to your antiquated, 50+ year old frame and suspension system.























Email Info@SchwartzPerformance.com for pricing & options.
-
Schwartz Performance Shop Update, May 2015
Check out the video below to view our latest shop updates & new projects! Video production by ARS Promotions
-
Full Floating Rear End Advantages – Pro Touring
All Schwartz Performance G-Machine Chassis are equipped standard with a Moser full-floating 9-inch housing/hubs etc.

-Your stock rear end is a non-floating setup. Standard GM and Ford 8.8 axles are held in with C-clips at the center of the rear end. If the clip breaks or the axle shaft snaps, the wheel can fall off since it’d bolted to the axle.
-Standard 9-inch Ford axles are held in by a bearing & retainer at the outside end of the rear end housing. If an axle breaks, there’s still a chance that the wheel can fall off.
-Full floating axles like we supply are held in by nothing. That’s right, they literally float inside the rear end. The full floating axles are SPLINED on both ends, so they only DRIVE the wheel and do not support the weight of the vehicle. With that said, they are much safer!
The main advantage that we use them for in the pro-touring world is to eliminate brake pad “knock-back.”
The standard GM & Ford axles that have C-clips holding them in, the axle can move side to side a bit, especially when cornering. You don’t need to be cornering hard for this to occur.
On a bearing-retained axle like the standard Ford 9-inch, the axle is held a little better, but there is still deflection under hard corners.Think about this:
-What bolts to a standard axle? The brake rotors and the wheels.
-What does your caliper bolt to then? The housing itself, which does not move.
-What happens when the axle deflects? Your rotor moves, but your caliper doesn’t- pushing your pads/pistons back into the caliper. Then the next time you go to hit the brakes, you need to pump them up to push the pads back out with the rotor.
Most upgraded calipers are fixed-mount. Some of the older 1 and 2-piston caliper designs are floating calipers, which have less of a tendency to push the pads back. On our G-Machine Chassis, we utilize a standard 4-piston Wilwood caliper, or the 6-piston Baer calipers which are both heavy duty fixed mount.
I still don’t get how the axle shaft works with the housing!
Think of your front spindle. It has a tapered snout that the bearings ride on, and the rotor fastens to. This is the same thing as a floating axle housing, but the spindle is large and hollow.
Here’s a picture of a bare housing with the “snout” or “spindle” welded on

Now here’s the hub assembly without the axle shaft or the splined drive plate installed. There’s a large nut that holds the bearings in, and a lock plate keeps it from loosening.

So why wouldn’t I want to go with a full-floating axle???
-Typically the cost is higher, but not by much. Our full floater adds only around $400 to the rear end cost, which isn’t much considering the advantages.
-Wheel fitment. A full floating setup has a large hub that sticks out from the wheel mounting surface. It is also a larger diameter. Some off-the-shelf cast wheels do not fit the floater very well, and either need the center bore machined larger, and/or a wheel spacer to allow the center cap to fit. If ordering custom wheels, you’ll need to specify the hub diameter & depth to be sure they fit.
-If you plan on upgrading the brake size down the road, there is cutting & welding required as the brake brackets are welded to the rear end housing. This is one of the reasons why we stick with a minimum of 13″ rotors, or 12″ if you’re using 15-16″ wheels.
Isn’t this a little overkill for my street car?
-If you’re never going to go around an exit ramp at an accelerated rate, run 7″ wide rear wheels, and have 250hp, yes.
-In all seriousness, full-floaters are becoming the norm in the pro-touring world, and offer more advantages than disadvantages. We’ve been using them as standard equipment since we started in 2005.Can I get a full floater setup on anything other than a Ford 9-inch housing?
-YES! We have done full floater 12-bolts, Dana 60’s, and even the Mopar 8.75.
Have any further questions? Shoot us an email at Info@SchwartzPerformance.com , or call (815)206-2230
-
Schwartz Performance Shop Update, April 2015
Check out the video below to view our latest shop updates & new projects!
Video production by ARS Promotions
-

1955–1957 Chevy Tri-Five Chassis

NOW AVAILABLE!
Your original Tri-5 chassis is inherently weak. Our G-Machine Chassis isn’t.
The old, non-braced frame that your suspension components and engine are mounted to begins to flex dramatically once you add more horsepower, higher spring-rates and better brakes; not to mention it’s nearly 60 years old. With our G-Machine Chassis, your car’s body will encounter much less flex and added ride quality, resulting in an all-around performing vehicle. Want to outhandle late-model sports cars? You’ve chosen the right chassis.
The G-Machine Chassis is available for 1955, 1956 & 1957 Chevrolet “Tri-five” cars:
- Chevy Bel Air / 150 / 210
- Nomad / Wagon / 4-door
Get the ultimate upgrade!
The G-Machine Chassis by Schwartz Performance.
Installation is simple.
- Our bolt-in design integrates original mounting points for the body and bumpers
- The stock gas tank can be utilized
Want wider tires?
- All G-Machine Chassis allow for up to 345mm-wide rear tires if you minitub the wheel wells
- The Moser full-floating 9″ rear end is built 60″ (custom rear end widths available)
Which options do I choose?
Brakes:
-Step up to the 14-inch Baer 6P Pro-Plus and get a brake system that will suit whatever you want to do. We race our 1965 Tempest often with this brake setup.
-The baddest kit is the Baer 6S, which is a one-piece forged caliper. This brake kit suits the hardcore roadracer, but does not sacrifice street driving.
-The 14″ brakes require a 18″ diameter wheel, however. Additionally, the Baer calipers are available in many colors.
Coilover shocks:
-We use RideTech coilovers as standard on our chassis systems. The two options we offer are single-adjustable and triple-adjustable.
-Single adjustable coilovers offer 24 “clicks” of adjustment for damping, as well as ride height adjustment. These will suit the weekend autocrosser/roadracer, as well as daily drivers.
-Triple adjustable coilovers offer the same damping adjustment as the singles with the addition of high and low speed compression adjustments, and a remote reservoir. These allow you to fine-tune your suspension for a specific type of driving. These are recommended for those who are willing & able to spend time tuning the shocks, and/or for the roadracer where every thousandth of a second counts.
-Air ride is also available, please call for pricing & info.
Rear end housing:
-Our standard axle is a Moser full-floating 9″ style housing, with 31-spline axles. We have tested this rear end up to 1000hp street cars with no issues. Contact us for higher HP, or if you’ll be drag racing it often on slicks with over 800hp. Not familiar with a full-floater? CLICK HERE FOR INFORMATION.
-The Heidts IRS option is for those craving an IRS in their musclecar. This is recommended for up to 700hp.
Third member/differential:
-The Ford 9″ comes with a clutch-type posi. Our first option is just that, with a cast-iron center section. If you have less than 500hp and won’t be racing the car often, this is just fine for you.
-The Detroit TrueTrac differential is a helical-gear type posi, which holds up to more power than the clutch posi, lasts longer (no wearable parts), and is quiet enough for street cars.
-Moser offers a new nodular iron case which is recommended for 600+ hp and racing. Their aluminum case also holds up to higher horsepower, and is much lighter than iron cases.Pictures:
(Click to enlarge)



















Base price includes:
- A fully-welded chassis, built on a precision jig
- Adjustable transmission crossmember
- Race-bred front and rear suspension components (excluding coilovers): control arms, ball joints, tie rods, NASCAR style sway bars, power rack & pinion, aluminum front wheel hubs with bearings, and teflon-lined heim joints for quiet & bind-free suspension
- BASE PRICE DOES NOT INCLUDE ANY BRAKES, SHOCKS, OR REAR END. CHOOSE THOSE ITEMS BELOW
Shipping:
- We ship assembled chassis using enclosed car transporters. If you order the chassis un-assembled, we’ll ship it via truck-freight in a crate. There is a crating fee, which will be determined upon ordering.
Pricing is for reference only. For questions, call 815.206.2230
Pricing:
-
Schwartz Performance: A World-Class Muscle Car Builder Based in Illinois
Looking to have your car modified and upgraded to the latest technologies? You’ve come to the right place.
Schwartz Performance has been building custom muscle cars, hot rods, and trucks for ten years now. We are not a general mechanic shop, nor a body/collision shop. We’re a custom car builder and performance shop. Our capabilities include but are not limited to: Chassis fabrication, engine building, sheet metal fabrication & panel fitment, complete wiring & stereos, mechanics & assembly, and performance parts consulting & sales. There is no job too big or too small!

Why would I want to modify my old car?
We’re the leader in bolt-in muscle car chassis, and install them into all of our major car builds. By adding a modern chassis to an old body, you get the handling & ride quality of a new car but the unique looks of a classic ride. Pair that with an Electronic Fuel Injection (EFI) system, or a modern engine, and you’ve got the performance you want out of your classic.
Sure, you (or anyone) can go to the Chevrolet dealer and spec out options for a new Corvette, and there are some options to choose from.. But we build your dream car! One that is 100% personalized for your tastes, retains a classic appearance, and can drive just as great as a new car. You can’t ask for much more than that. Additionally, nobody else can go out and buy exactly what you have us build. Each vehicle is unique.

What’s Schwartz Performance’s specialty?
We build cars that are able to be driven, and driven comfortably. We don’t build trailer queens!
Most of our builds have ended up in magazines, won awards at car shows, and won racing events, and have the ability to do all of those at the same time. Take a look at our Completed Projects page to get a look at the type of builds we do.Why should I have Schwartz Performance build my car as opposed to another shop?
-We don’t cut corners. Our team is made up of professionals to get each task done correctly.
-As stated earlier, our cars are built to be driven. We use all new components, not inferior or used parts that would sacrifice the quality.
-We operate a clean, organized shop, and have the efficiency to work on many projects at once. The labor hours we put forth are spent working on the car, not looking for tools scattered all over the bench.
-We have strong relationships with manufacturers. This strengthens our reputation as a builder, as many manufacturers have strict policies in place to weed out the “fly by night” shops.
-Worldwide name: We’ve built cars, engines, and put together parts packages for customers in over 25 different countries.
-Jeff Schwartz’s background: Most of Jeff’s career was in tool & die, and manufacturing. He managed a few different plants in the Chicagoland area, and was a hobbyist in the automotive field. Jeff also has a racing background, including wins in SCCA and IMSA series.
-Celebrating 14+ years in business!!
How long does a build take?
-A complete build from teardown to completion takes anywhere from 9-14 months. Smaller jobs not requiring panel replacement and paint jobs take much less time. On average, our full builds have 1100-1400 man hours put into them. It all depends on the scope of the project, and the condition of the project car.
If you’re interested in having us modify your ride or build one from the ground up, contact Jeff Schwartz or Dale Schwartz at:
(815)206-2230
Info@SchwartzPerformance.com
Schwartz Performance is based out of Woodstock, Illinois and is owned by Jeff Schwartz and operated by him and his team of 14 employees.
-
Schwartz Performance Shop Update, March 2015
Check out the video below to view our latest shop updates & new projects!
Video production by ARS Promotions
