Author: Schwartz Performance

  • MotoFeet Engine Stands

    Do you have an engine that needs to sit in the garage for a bit, or hang out in your showroom?
    Then you need a MotoFeet stand!

    Schwartz Performance stocks many MotoFeet stands for GM & Ford applications. Steel and rubber casters are also available but not necessary for use. We recommend steel casters if the engine will be stored for a long period of time, as rubber may flat-spot over time.

    Don’t confuse these with cheap Chinese-made stands, OR stands that need to bolt to the back of the engine block. MotoFeet fasten in 2 pieces to the sides of the engine only, so the engine & transmission do NOT need to be separated!

    SALE PRICE: $75 FOR ANY MOTOFEET STAND, and $110 FOR STANDS WITH CASTERS!

    (Normally $85 without casters and $120 with casters)
    Please allow 24-72 hours for shipping.

    To order, give us a call, or click: https://www.schwartzperformance.com/product/motofeet-engine-stands

    Available for:
    GM/Chevy: Small block 305/350/400 etc, Big block 396/427/454 etc, 409, LS1/2/3/6/7/9/A

    Ford: Small block 289/302, Ford big block, Ford Coyote / Modular 4.6 5.0 5.4 L

    sbf motofeet with casters
    LS1(1)
    bbc2
    steel casters
    rubber casters
  • 1978–1988  G-Body, Regal, Monte Carlo Chassis

    1978–1988 G-Body, Regal, Monte Carlo Chassis

    78-87_GBody_Header

    Get the ultimate upgrade!

    The G-Machine Chassis by Schwartz Performance.

    • 200% less torsional flex than stock
    • 119lbs less than stock, roller-to-roller (with identical wheels/tires)

    Available for 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987 and 1988 GM G-bodies:

    • Chevrolet Monte Carlo
    • Chevrolet Malibu
    • Chevrolet El Camino
    • Buick Regal
    • Oldsmobile Cutlass
    • Pontiac Grand Prix

    Installation is simple.

    • Our bolt-in design integrates original mounting points
    • The stock gas tank is moved from an offset placement, to a centered placement— new gas tank strap brackets are included
    • The spare-tire well is removed—replacement piece is included

    Want wider tires?

    • All G-Machine Chassis allow for up to 345mm-wide rear tires if you minitub the wheel wells (Or up to a 14″ wide wheel)
    • The Moser full-floating 9″ is narrowed to 58″ to allow for deeper dish on the rear wheels (lower offset wheels)

    Which options do I choose?

    Brakes:

    -Step up to the 14-inch Baer 6P Pro-Plus and get a brake system that will suit whatever you want to do. We race our 1965 Tempest often with this brake setup.
    -The baddest kit is the Baer 6S, which is a one-piece forged caliper. This brake kit suits the hardcore roadracer, but does not sacrifice street driving.
    -The 14″ brakes require a 18″ diameter wheel, however. Additionally, the Baer calipers are available in many colors.

    Coilover shocks:

    -We use RideTech coilovers as standard on our chassis systems. The two options we offer are single-adjustable and triple-adjustable.
    -Single adjustable coilovers offer 24 “clicks” of adjustment for damping, as well as ride height adjustment. These will suit the weekend autocrosser/roadracer, as well as daily drivers.
    -Triple adjustable coilovers offer the same damping adjustment as the singles with the addition of high and low speed compression adjustments, and a remote reservoir. These allow you to fine-tune your suspension for a specific type of driving. These are recommended for those who are willing & able to spend time tuning the shocks, and/or for the roadracer where every thousandth of a second counts.
    -Air ride is also available, please call for pricing & info.

    coilover options1

    Rear end housing:

    -Our standard axle is a Moser full-floating 9″ style housing, with 31-spline axles. We have tested this rear end up to 1000hp street cars with no issues. Contact us for higher HP, or if you’ll be drag racing it often on slicks with over 800hp. Not familiar with a full-floater? CLICK HERE FOR INFORMATION.
    -The Heidts IRS option is for those craving an IRS in their musclecar. This is recommended for up to 700hp.

    housing options2

    Third member/differential:

    -The Ford 9″ comes with a clutch-type posi. Our first option is just that, with a cast-iron center section. If you have less than 500hp and won’t be racing the car often, this is just fine for you.
    -The Detroit TrueTrac differential is a helical-gear type posi, which holds up to more power than the clutch posi, lasts longer (no wearable parts), and is quiet enough for street cars.
    -Moser offers a new nodular iron case which is recommended for 600+ hp and racing. Their aluminum case also holds up to higher horsepower, and is much lighter than iron cases.

    Pictures:

    (Click to enlarge)

    Base price includes:

    • A fully-welded chassis, built on a precision jig
    • Adjustable transmission crossmember
    • Race-bred front and rear suspension components (excluding coilovers): control arms, ball joints, tie rods, power rack & pinion, aluminum front wheel hubs with bearings, and teflon-lined heim joints for quiet & bind-free suspension
    • BASE PRICE DOES NOT INCLUDE ANY BRAKES, SHOCKS, OR REAR END. CHOOSE THOSE ITEMS BELOW

    Shipping:

    • We ship assembled chassis using enclosed car transporters. If you order the chassis un-assembled, we’ll ship it via truck-freight in a crate. There is a crating fee, which will be determined upon ordering.

    Pricing is for reference only. For questions, call 815.206.2230

    Pricing:

    View the current chassis profile

  • 1968–1972  A-Body,  GTO, Cutlass, Chevelle Chassis

    1968–1972 A-Body, GTO, Cutlass, Chevelle Chassis

    68-72_a_Header

    Details:

    Bolt-in modern high-performance chassis for 1968, 1969, 1970, 1971 and 1972 GM A-Bodies.

    • Chevrolet Chevelle
    • Pontiac GTO / Lemans / Tempest
    • Oldsmobile Cutlass
    • Buick Skylark / GS
    • Our A-body is torsionally 200% stiffer than the stock A-body frames, & weighs 125lb LESS, roller-to-roller.

    Installation is simple.

    • Our bolt-in design requires NO floor cutting or fabrication.
    • The rear rails are narrowed to accommodate minitubs
    • Since our rails are narrowed, a narrowed fuel tank is required. We can supply a stainless steel tank to fit our chassis.

    Want wider tires?

    • All G-Machine Chassis allow for up to 345mm-wide rear tires if you minitub the wheel wells
    • The Moser full-floating 9″ is narrower than stock (58″ wheel to wheel) to allow for deeper dish on the rear wheels (lower offset wheels)

    Which options do I choose?

    Brakes:

    -Step up to the 14-inch Baer 6P Pro-Plus and get a brake system that will suit whatever you want to do. We race our 1965 Tempest often with this brake setup.
    -The baddest kit is the Baer 6S, which is a one-piece forged caliper. This brake kit suits the hardcore roadracer, but does not sacrifice street driving.
    -The 14″ brakes require a 18″ diameter wheel, however. Additionally, the Baer calipers are available in many colors.

    Baer brake rotors and calipers

    Coilover shocks:

    -We use RideTech coilovers as standard on our chassis systems. The two options we offer are single-adjustable and triple-adjustable.
    -Single adjustable coilovers offer 24 “clicks” of adjustment for damping, as well as ride height adjustment. These will suit the weekend autocrosser/roadracer, as well as daily drivers.
    -Triple adjustable coilovers offer the same damping adjustment as the singles with the addition of high and low speed compression adjustments, and a remote reservoir. These allow you to fine-tune your suspension for a specific type of driving. These are recommended for those who are willing & able to spend time tuning the shocks, and/or for the roadracer where every thousandth of a second counts.
    -Air ride is also available, please call for pricing & info.

    coilover options1

    Rear end housing:

    -Our standard axle is a Moser full-floating 9″ style housing, with 31-spline axles. We have tested this rear end up to 1000hp street cars with no issues. Contact us for higher HP, or if you’ll be drag racing it often on slicks with over 800hp.
    -The Heidts IRS option is for those craving an IRS in their musclecar. This is recommended for up to 700hp.

    housing options2

    Third member/differential:

    -The Ford 9″ comes with a clutch-type posi. Our first option is just that, with a cast-iron center section. If you have less than 500hp and won’t be racing the car often, this is just fine for you.
    -The Detroit TrueTrac differential is a helical-gear type posi, which holds up to more power than the clutch posi, lasts longer (no wearable parts), and is quiet enough for street cars.
    -Moser offers a new nodular iron case which is recommended for 600+ hp and racing. Their aluminum case also holds up to higher horsepower, and is much lighter than iron cases.

    Pictures:

    (Click to enlarge)

    Base price includes:

    • A fully welded chassis, built on a precision jig
    • Adjustable transmission crossmember
    • All front and rear suspension components (minus coilovers): control arms, ball joints, tie rods, power rack & pinion, aluminum front wheel hubs with bearings, and teflon-lined heim joints for a quieter & bind-free suspension

    Payment terms: 75% down at time of order, remaining 25% due before shipment.

    Shipping: For an assembled frame, we use an enclosed car transporter. If you don’t want the frame assembled, we’ll ship it truck freight in a crate. There is a crating fee which will be determined upon ordering.

    Pricing below is only for reference. Please call to order.

    Pricing:

    View the current chassis profile

  • 1964–1967  A-Body,  GTO, Cutlass, Chevelle Chassis

    1964–1967 A-Body, GTO, Cutlass, Chevelle Chassis

    64-67_Abody_Header

    Get the ultimate upgrade!

    The G-Machine Chassis by Schwartz Performance.

    • 200% less torsional flex than stock
    • 125lbs less than stock, roller-to-roller (with identical wheels/tires)

    Available for 1964, 1965, 1966 and 1967 GM A-Bodies, including convertibles:

    • Chevrolet Chevelle
    • Pontiac GTO / Lemans / Tempest
    • Oldsmobile Cutlass
    • Buick Skylark / GS
    • El Camino & Wagons

    Installation is simple.

    • Our bolt-in design requires NO floor cutting or fabrication.
    • The rear rails are narrowed to accomodate minitubs
    • “Body-dropping” can be done, but requires more significant fabrication.
    • Since our rails are narrowed, a modified or narrow fuel tank is required.

    Want wider tires?

    • All G-Machine Chassis allow for up to 345mm-wide rear tires if you minitub the wheel wells
    • The Moser full-floating 9″ is narrowed to 58″ overall, to allow for deeper dish on the rear wheels

    Which options do I choose?

    Brakes:

    -Step up to the 14-inch Baer 6P Pro-Plus and get a brake system that will suit whatever you want to do. We race our 1965 Tempest often with this brake setup.
    -The baddest kit is the Baer 6S, which is a one-piece forged caliper. This brake kit suits the hardcore roadracer, but does not sacrifice street driving.
    -The 14″ brakes require a 18″ diameter wheel, however. Additionally, the Baer calipers are available in many colors.

    Baer brake rotors and calipers

    Coilover shocks:

    -We use RideTech coilovers as standard on our chassis systems. The two options we offer are single-adjustable and triple-adjustable.
    -Single adjustable coilovers offer 24 “clicks” of adjustment for damping, as well as ride height adjustment. These will suit the weekend autocrosser/roadracer, as well as daily drivers.
    -Triple adjustable coilovers offer the same damping adjustment as the singles with the addition of high and low speed compression adjustments, and a remote reservoir. These allow you to fine-tune your suspension for a specific type of driving. These are recommended for those who are willing & able to spend time tuning the shocks, and/or for the roadracer where every thousandth of a second counts.
    -Air ride is also available, please call for pricing & info.

    coilover options1

    Rear end housing:

    -Our standard axle is a Moser full-floating 9″ style housing, with 31-spline axles. We have tested this rear end up to 1000hp street cars with no issues. Contact us for higher HP, or if you’ll be drag racing it often on slicks with over 800hp.
    -The Heidts IRS option is for those craving an IRS in their musclecar. This is recommended for up to 700hp.

    housing options2

    Third member/differential:

    -The Ford 9″ comes with a clutch-type posi. Our first option is just that, with a cast-iron center section. If you have less than 500hp and won’t be racing the car often, this is just fine for you.
    -The Detroit TrueTrac differential is a helical-gear type posi, which holds up to more power than the clutch posi, lasts longer (no wearable parts), and is quiet enough for street cars.
    -Moser offers a new nodular iron case which is recommended for 600+ hp and racing. Their aluminum case also holds up to higher horsepower, and is much lighter than iron cases.

    Pictures:

    (Click to enlarge)

    Base price includes:

    • A fully-welded chassis, built on a precision jig
    • Adjustable transmission crossmember
    • Race-bred front and rear suspension components (excluding coilovers): control arms, ball joints, tie rods, power rack & pinion, aluminum front wheel hubs with bearings, and teflon-lined heim joints for quiet & bind-free suspension

    Shipping:

    • We ship assembled chassis using enclosed car transporters. If you order the chassis un-assembled, we’ll ship it via truck-freight in a crate. There is a crating fee, which will be determined upon ordering.

    Pricing is for reference only. For questions, call 815.206.2230

    Pricing:

    View the current chassis profile

  • Kevin’s 1966 Mustang

    Kevin’s 1966 Mustang

    You may know Kevin Tetz from the television show Trucks! on SpikeTV. He just finished his ’66 Mustang for the 2012 SEMA show, using a Schwartz Performance G-Machine Chassis as it’s foundation. He used modern Mustang components on the engine and interior, and even integrated newer Mustang headlights into the fenders and front fascia.   Look for this car in an upcoming issue of Popular Hot Rodding! (Late 2013 – Early 2014)

  • Martin’s 1968 Charger

    Martin’s 1968 Charger

    Martin has been working on his 1968 Charger for several years. That’s because there’s a lot of rust repair to go, not to mention college took up a lot of the time & funds!

    For information on his build, CLICK HERE (You will be directed to the Dodge Charger forums).

  • BeCool IceBird

    A-Team Racing built the Be Cool Bomber Chevelle for SEMA 2010 using a Schwartz chassis, and decided to use us again for their 2011 SEMA build, a 1968 Firebird with a twin turbo LS engine.

  • 1968–1970  B-Body, Coronet, Road Runner, Charger Chassis

    1968–1970 B-Body, Coronet, Road Runner, Charger Chassis

    68-70_Bbody_Header

    Your Mopar’s uni-body construction is inherently weak. Our G-Machine Chassis isn’t.

    Introducing the FIRST and ONLY bolt-in full frame / chassis for your Mopar unibody!
    Thinking about running a 1000hp Hellephant engine? Your stock unibody isn’t going to hold up to that 1000hp monster. Our chassis will, though!

    The sheet-metal that your suspension components and engine are mounted to begins to flex dramatically once you add more horsepower, higher spring-rates and better brakes. With our G-Machine Chassis, your engine, rear-end, steering and suspension are isolated from the body. The G-Machine Chassis becomes the main support for your car and the uni-body structure simply becomes added support, helping to tie together the G-Machine Chassis.

    The G-Machine Chassis is available for 1968, 1969 & 1970 Mopar B-Bodies:

    • Dodge Charger
    • Dodge Coronet
    • Dodge Super Bee
    • Plymouth Road Runner
    • Plymouth Satellite
    • Plymouth GTX

    Installation is simple.

    • The only required cutting is of minor brackets, front frame-rails and front shock towers—creating a “clean” engine bay; As well as a notch in the rear footwell of the factory floorpan. This does not impede the driver’s area at all.
    • The only required welding is of four mounting plates onto the original torsion bar cross-member, and a few reinforcement plates & tube sleeves to the factory rear rails.
    • The only required drilling is of two bolt-holes in each of the rear frame rails

    Want wider tires?

    • All G-Machine Chassis allow fitment of up to 345mm-wide rear tires if you minitub the wheel wells
    • The Moser full-floating 9″ is narrowed to 58″ hub-to-hub to allow a deeper dish on the rear wheels

    Which options do I choose?

    Brakes:

    -Step up to the 14-inch Baer 6P Pro-Plus and get a brake system that will suit whatever you want to do. We race our 1965 Tempest often with this brake setup.
    -The baddest kit is the Baer 6S, which is a one-piece forged caliper. This brake kit suits the hardcore roadracer, but does not sacrifice street driving.
    -The 14″ brakes require a 18″ diameter wheel, however. Additionally, the Baer calipers are available in many colors.

    Baer brake rotors and calipers

    Coilover shocks:

    -We use RideTech coilovers as standard on our chassis systems. The two options we offer are single-adjustable and triple-adjustable.
    -Single adjustable coilovers offer 24 “clicks” of adjustment for damping, as well as ride height adjustment. These will suit the weekend autocrosser/roadracer, as well as daily drivers.
    -Triple adjustable coilovers offer the same damping adjustment as the singles with the addition of high and low speed compression adjustments, and a remote reservoir. These allow you to fine-tune your suspension for a specific type of driving. These are recommended for those who are willing & able to spend time tuning the shocks, and/or for the roadracer where every thousandth of a second counts.
    -Air ride is also available, please call for pricing & info.

    coilover options1

    Rear end housing:

    -Our standard axle is a Moser full-floating 9″ style housing, with 31-spline axles. We have tested this rear end up to 1000hp street cars with no issues. Contact us for higher HP, or if you’ll be drag racing it often on slicks with over 800hp.
    -The Heidts IRS option is for those craving an IRS in their musclecar. This is recommended for up to 700hp.
    -We can also provide Mopar housings for those interested. Please call for information & pricing.

    housing options2

    Third member/differential:

    -The Ford 9″ comes with a clutch-type posi. Our first option is just that, with a cast-iron center section. If you have less than 500hp and won’t be racing the car often, this is just fine for you.
    -The Detroit TrueTrac differential is a helical-gear type posi, which holds up to more power than the clutch posi, lasts longer (no wearable parts), and is quiet enough for street cars.
    -Moser offers a new nodular iron case which is recommended for 600+ hp and racing. Their aluminum case also holds up to higher horsepower, and is much lighter than iron cases.

    Pictures:

    (Click to enlarge)

    Base price includes:

    • A fully welded chassis, built on a precision jig
    • Adjustable transmission crossmember
    • All front and rear suspension components (excluding coilovers): control arms, ball joints, tie rods, power rack & pinion, aluminum front wheel hubs with bearings, and teflon-lined heim joints for a quieter & bind-free suspension
    • BASE PRICE DOES NOT INCLUDE ANY BRAKES, SHOCKS, OR REAR END. CHOOSE THOSE ITEMS BELOW

    Shipping:

    We ship assembled chassis using enclosed car transporters. If you order the chassis un-assembled, we’ll ship it via truck-freight in a crate. There is a crating fee, which will be determined upon ordering.
    Pricing is for reference only. For questions, call 815.206.2230

    Pricing:

    View the current chassis profile